How do you choose the second-stage retardator 1:71 on the squeezer? The material is placed in the inlet tank, the material is placed on the discharge shelf, the pressurizer is activated, the slower wheel wheel drives the slider for a horizontal back-to-back exercise, the slider pushes the wheel for leverage, the material on the shelf is pushed to the lower end of the frame into the landing wheel, when the landing tank passes, the material goes into the faller tank and rolls with the faller wheel, and when the faller sink starts to turn down, the material falls into two pressurized wheels for squeezing treatment. You can follow the detailsGeared motorSelective technical staff communicate further and then determine the model. These are some of the details of the user equipment, but at this point it is not known what parameters it requires, but we need to consider how much force the overall squeezer takes to drive its equipment in the course of its operation. If it is more powerful, then the output of the twister is the relatively larger reduction model. The seat is fixed on the upper end of the fixed shelf, the seat described is on both sides of the landing vent, there is a perforation on both the rear and the rear side wall of the seat, and the axis runs through the centre of the squeeze wheel and is attached to the perforation. The centre of both gears is placed on the back of the corresponding rotor, and the gears are on the back of the squeezing wheel, where the two gears converge. The electric power plant is attached to the side wall behind the pressurized box, and the electric axis of the electric power plant runs through the side wall behind the squeezer and is connected to the first turning axis on the left side through the axis。

The number of landing tanks is four and the four landing tanks are set at 90° in a neighbouring angle to reduce the need to use a large amount of scales to slow down the landing, reduce the burden on the electric power and the useful life of the progressive squeezer. It's fixed to the top of the pressurized box, and it's in the back of the squeezerHorizontal reducerIt is connected by a joint axis between the axle and the rotor. The squeezing device consists of a squeezing tank, two squeezing wheels, two installed seats, one electric generator, two first axis and two gears. His squeezer, including the feeder, the squeezer and the compressor. One end of the pole is fixed to the front end of the rotor and the other is related to the second end of the pole, which is formed through the distribution column through the left end of the pole, all of which are symmetrically set around the central line of the input box. Or you can download the corresponding decelerator selection information and look at the details of the parameters that the user uses as a driver for his squeezer, when you choose the corresponding electric gear-reducing machine, at a rate of 71, but it is not possible to determine the model because there is only one parameter, at a time you look at the drive or drive that is connected to thereducing machine, the load that it drives and the of the operation, and look at some details of the user device. Let's take a look today at a case that requires a 71-to-oneretard to use on his squeezerDouble- power deceleratorAnd what should be considered。

It is as if, during the production of aluminium alloy, a device called a pressurizer is often used, which needs to be driven, and he needs an electric power to work with him. At this time, there are many options for the power source, and some users choose to use an electricreducing machine as the main driver, but not all users know how to do so when choosing an electric brake. The feeding devices include feed boxes, landing wheels, electric machines, poles, slides, pushers, sliders and rotors. The feeder box is fixed at the top of the squeezing tank, with an input port at the top of the input box, a discharge frame on the right side of the input box, a landing wheel installation spot on the bottom of the input box, a turner hole on the side wall close to the landing wheel, a turner at the landing wheel, a turner at the centre of the landing wheel and a turner on the ammonium side wall. It's a useGearbocthe output twist is driving. during the production of certain industrial products, it is similar to non-ferrous metal-structured materials, which need to be squeezed and then further shaped according to actual demand, a process that is often difficult to manipulate by humans, so it is generally chosen to be supported by some large integrated and intelligent machines. http://boserlgearreducer.com/product/list-saxiliejiansuji-cn.html