The case of scalding snails with slashing gears on the sledgehammer, 71.5 retrofits per minute. However, there are no more parameters to calculate in the above-mentioned cases and therefore the model cannot be determined for the time being. The clamp consists of a fixed section that is attached to the rig, a fitting section that is attached to the fittings, a link to the other end of the fixed section that is connected to the connection to the fittings, a slider on the side that is attached to the rigs, which prevents the disengagement of the clips, a threaded hole that is placed in the direction of the fittings, a screwdriver that is fitted with a screwdriver, a bolt that exits the fittings, and a pentipal end that exits and exits to the pieces。Double-polar slowing machineThe wood has been pre-processed from the logs by drying, crushing, etc., and the wood is more flat on all sides, so that the wood does not itself undergo rotation or other movement except for the assembly. Let's look today at the selection of the engine type of the wood roller snail snail. In order to avoid the wideness of wood, which could be cut by a knife, if the wood moves in its own tilt scroll, the size of the wood can be increased. To avoid this, the plate rises to a limited panel, with a slide from one end of the limit plate connected to a limited pole, a screwdow connected to the other end of the thread, which is connected to the second plate, and a set of slashed gears attached to the snailsGeared motorThe driver's screwdriver is attached to the second plate, with the limit plate coming close to the docked wood, which is placed between the limit plate and the assembly; the limit rod primarily prevents the limit plate from rolling around the screwdriver. What needs to be exaggerated is that a limit plate is a preposition to wood, not a pretense to wood, so that the movement of wood along the assembly is not affected by the limit plate。

In the user selection process, his request was to use a snail-slasher snail sled with a slasher, and it would be more appropriate to match the power with the output machine at 71.5 turns per minute. Then look at some of the user’s equipment. In the selection of a user last week, his request was to use an electric setMotor gearedAt a time when the requirement is to use a snail snail snail slasher with a slanted gear to fit into the electric machine, how would it be appropriate to match it? The user is a lumber-turner machine, which he uses as a power-driven grinder and cutting device. The repositioning of the assembly is followed by the repositioning of four sets of packagings to the assembly and manoeuvring table, which closely connects the packaging itself, the assembly and the rigging to one and limits the movement of the assembly relative console; the wood that will need to be processed will be placed at the interface of the plate and will be moved in an extension direction along the line of the plate, at which point the limit plate will be drawn to limit the rolling of the wood itself through the scroll of the screwdriver。

It then turns on the gear snail-reducing machine, which rotates the blades at a high, driven by the snail-reducing machine of the stooge, and the wood moves along the line of the plate and is cut by the blade, and the wood is processed in a rewinding corner, and the carpenter can complete the round-reverse processing of the wood, based on the converse of the other positions designed to reprocess the wood. At this time, it is proposed to use a variable frequency power machine to match the s37/s47/557 reduction model for a combination of such carpentry machines. There is sometimes a need to use a great deal of mechanical equipment during wood processing, as if wood were rounded or decorated. when the costumes were installedServo motor reducerThe fixed part of the motor-driven automation device drive is attached to the lower end of the rig, which is then placed on the upper end of the rig, and, through the rotor screw, the binder is attached to the rig and the suit, and the four are manipulated in a sequential manner. This is some of the cases of the power-reducing machines used by users on the rounded-angle machine. Detailed information may be obtained on the configuration of the detailed parameters by consulting a selected machine technical staff for the Boserl snail brake snail or by downloading samples of the snail snail snail snail sled. http://boserlgearreducer.com/product/list-wolunwomenjiansuji-cn.html