2. 2 kw retrenchor matches thereducing power unit manufacturer and then reaches 40 to be used on a silk pole lift? At this point, the range of the deceleration ratio was between 3. 98 and 4370, and at that time there was 40. 04 of the parameters, which was not significantly different from the actual deceleration ratio, so the paragraph could be used. in the absence of a specific type ofreducing unit manufacturer to match, we use four major seriesGeared motorLet's see what the model of the manufacturer of thereducing unit is. At that time, the parameters he obtained by way of calculation were a 40-to-40 cut-off ratio after the combination of thereducing power unit and the matching power plant he chose to use 2. 2 kw. At this time, the correspondingreducing unit manufacturer was r87. Correspondingreducing power unit producers are f67 motor unit producers. But we're looking at a single one--down power plant model, not a combination, and why? In the process of using one--down power plant, a single one- power plant can achieve a relatively small cut. At this time, there was no 40, which was closer to 41. 07, the corresponding model being the s77 one-stop machine manufacturer. on some lifts, a mechanical called a lifter is often used。

And in the process of a user's use, not long ago, he would have preferred that we should have let his silk lifter choose the corresponding electric power and thereducing power unit manufacturer use the operation of the elevator above. Which of these parameters can we chooseMotor gearedWhat about matching? In this case, we use this user's case to look at the electrics used on the wire lifts and the selection process of the one-size-fits-all producers. This is a self-locked one-stop machine manufacturer, which can be matched with a 2. 2-kw match: s57 one-stop machine, s67 one-man, s77 one-man, s87 one-man, s97 one-man, and a combination of models are serviceable. If one were to be matched by one of thereducing machines, the model of the one of the slow-reducing machines would be operational at this time, from r27 to r107 and some of the combinations of one of thereducing machines, at a time when the list of parameters of one of the bolserl-reducing machines was not exactly 40, while it was closer to 41. 74. In the absence of specific requirements, the matching of the s-seriesreducing unit generators was limited. At this point, the rate-reducing ratio ranged from 7. 28 to 420 and the user requested 40, so it was within this range. The list of parameters at this time is not exactly 40, which is closer to 39. 26. then it's the sameGeared motorThe model is either a k-77-reducing power plant or a ka-77-reducing power plant, a kf-77-reducing power plant, and a kaf-77-reducing power plant. the more suitable one-stop machine manufacturer forreducing machines is the one-man company for k-seriesreducing machines

If a match is made with a k-seriesreducing unit manufacturer, the model for areducing unit manufacturer would be k37, k47, one machine, k57, one, k67, one, k77, one, k87, one, k97, one, and six-dollar. However, the deceleration ratio after the combination will become significant in terms of the deceleration ratio, as the slowdown ratio of the combined deceleration unit generator to the manufacturer of the two slowing machines will be larger than the product of the product. the detailed selection of which type of equipment is to look at the form of installation and then select an appropriate option based on these requestsParallel axle reduction powerIf matched, there is also a large number of models for thereducing unit manufacturer that can be matched at this time, and in such a case thereducing unit manufacturer can be matched from the F27 to F107 and some combinations. Like the K107 one-stop machine manufacturer, it can't match. This machine can assist other equipment in operating to meet the requirements for its use in different environments. http://boserlgearreducer.com/product/list-rxxiilijiansuji-cn.html