3-380v370w 3-to- 60-to-60, which one to use? And now, in the selection of a user, he's asked to match the three- reduction machines with a three- reduction machine of three-hundred-thirty-five-five-five-five-five-five-five. now, what three- reduction machines would be able to meet his requirementsbrakes motor-reducerWhat are the models. The list of parameters at this time is not exactly 60-to-60. But closer to 61. 30. Regardless of which three-to-three reduction machines are used for matching, at this time, a 370w variable frequency power plant is required. The list of parameters at this time was also not exactly 60, which is closer to 58. 32, when the corresponding three-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one. Each of these devices will be used for the drive, which may be electric, motor, three-paced, etc. This compares to rx573 with rx673 with r173 with r873 and - a combination of three- reduction models can match the equipment, where the rate ratio ranges from 1. 65 to 7307. in a situation where the user's demand top user does not make a requirement for the type of triple-reducing power, or for the mode of output of the triple-reducing power, we need to provide, as far as practicable, different modes of output and different types of k seriesGeared motorMake a match. The range of the deviance ratio that can be formed in the 370w power machine matched with the k-six-six-six-six-six-six-six-six-six. The deceleration ratio at this time ranges from 9. 02 to 2054. At this point, it is closer to the user's requirements, and the corresponding three-stagereducing machine is r273 or rf273 -- the output is up to 157nm.

Different equipment is required for each device in different working environments, and in this case we need to consider the actual use and choose the corresponding device to match it to the mechanical master. If the choice is..GearbocThe plant matches, at which point there are many models of three-stage reduction machines that can be matched. In the course of using it, we chose to use four series of three--down machines for matching, at which point there were two types of three--down machines and three types of output. The s-series snail snails are then matched by a three--down machine, which can be matched by three--down machines, from the s373 to the s873 and a three--down power unit of the three. Close to 63. 33, the corresponding three-stage reduction machine at this time was the s37-trigger. When matched by the f series parallel axle three--reducing machines, the three--reducing machines that can be matched at this time are f27-trigger-to-f87-trigger and a combination of three-velocity-reducing machines. The list of parameters at this time is not exactly 60-to-60. At this time, the rate of deceleration compared with the three-phased three after the 370w mix was 4. 16 to 6715. The list of parameters at this time is not exactly 60-to-60, which is closer to 63. 3 or 58. 6, at which point the corresponding three-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one-to-one. and the k seriesSpiral cone gear deceleratorIf matched, the type of three-stagereducing machine that can be matched at this time is within the range of K47-trice-trigger to K87-trice, as well as the seven-tempor and three-temporal. Different devices are used differently, so the selection of the device is also one-on-one. http://boserlgearreducer.com/product/list-fafxilijiansuji-cn.html