A set of brakes for the hanger and the electric. The brake impact cannot exceed the design specifications. However, for safety reasons, both of these two sets can be selected on downward transport carriers, where hydraulic pusher brakes are used as a backup. Therefore, transmitters that do not require a change in the power rectangular size for their work may not be used. If the control system is subject to a broad title, it is easy to cross the brake-capacitation accident, if it is not handled in a timely manner, causing the brake-plastics to burn down, liquid-coincidence protection, overloading of the electric power, which can lead to a fire in the event of a serious event. So..Vertical reducerThe set of transmitters with them must be observed when they start and stop. The system must simulate emergency brakes for a load test. The light and individual brake wheels are badly worn, while the heavy is the damage to the conveyor belt. The joint axle between the electric andreducing engines is often designed for the elastic joint axle and the brake congener; for large-band transporter systems, a liquid axle is required between the electric and the elastic axle in order to start the pace and achieve mechanical overload protection。

two types of brakes, like a set of brakes, are recommended for the use of disc brakes and hydraulic pushers. when the multi-drive is coupled with the drive, the system brake balance shall be ensured. the of the round of the gear round can be as high as 50-80 ms, with a high-precision, well-balanced set of gears。Servo motor reducerA set of attentions to the daily use of brakes with electrics: brakes are often used for axle sales to lubricate maintenance to prevent brakes from acting in a less agile manner. The gear axle segment is scheduled to use a high-pressure lithium-based lubrication to reduce the wear and tear of the teeth and to extend the service life of a set of gear axle bands with the crane. The turbo-axis are used as a joint axle between a crane and an electric set and a driver ' s roller; when the axis of a gear-axis is 18 to 560 mm, the corresponding bend is 710 to 1,000,000 N.m, with a turn-rate of 3780 to 300 rpm, and it is agreed to move to 0.4 to 6.3 mm (anggle-to-0 and otherwise smaller) and to 3° when the drums are used. While the former power rectangles can be adjusted at work and combined with the transport engine for downward transport, the latter power rectangles can only be adjusted prior to start-up and are recommended for promotion or horizontal transport machines。

Because the load is hangingGeared motorthe distribution on the cortex is complex with the set of cortex knots, which makes it difficult to calculate the strength and lifetime of the cortex. the liquid-crusher brakes are to be kept in the right position, and the oil levels are too low for the subject of the failure of the brakes. the brake parts of the crane and the motor set are resistant to erosion. a set of brakes for cranes and electric generators: a brake can be set up by a mounted transmitter, as required, to ensure that, in case of emergency brakes, the leak in the transmission system is not blocked. in the case of multiple generators driving the same conveyor belt at the same time, the sequence and timing of brakes of the various mechanisms of the brake set of the hanger and the electric generators must be strictly adjusted to the design requirements. hangers and electric circuits are also commonly used in high- transmissions, calculated on the basis of a round velocity of 15 ms on the round of gears, when the high given in the scale is 15 ms。Gearbox motora set of plate brakes with electric power is better than a hydraulic pusher, but is complex and expensive. the brake's power rectangles and brake time are regularly adjusted to meet the requirements of the system. the brakes ' brakes, because of the accuracy of their installation, are prone to a loss of rounding, which, if severe, requires a timely replacement or damage to the power and other transmissions. otherwise, the subject of brakes and system mismatches can easily arise. the liners are designed to be easily replaced and consist of grinding material. it is generally recommended for use on down-to-down transport carriers operating at a general negative power level in order to satisfy the requirements for a smooth start and mind. it is generally possible to select the appropriate coaxial size from the scale by calculating the twist. http://boserlgearreducer.com/product/list-safxiiejiansuji-cn.html