Four radiant rollers, a series ofreducing snails, were prevented. large end cap improvement of pressurized device: mechanical moving structure under pressureRight-angle shaft reducer motorwhen the snail axle fails, if the large end covers are heavy (approximately 183 kg) and the manpower cannot be removed, installed, it requires a car to accompany the lift, and the space is small and the subject is dealt with for longer periods. (1) to improve electrical chain protection and maintain online detection elements, such as high-temperature meters, and, if necessary, to increase the of detection by adding wind fans to blow out smoke and fog, and to enhance education, testing, responsibility for progress and manipulation in a hand-held state to ensure that the phenomenon is not pushed down during roll-up. after a few hours of operation, there will always be some malfunctions, such as pressurizing mechanical transmission structuresSa series deceleratora total of seven snail axle malfunctions occurred in the year, causing a breakdown of more than 30 hours. the re-engineering will allow for the opening of a 380 mm diameter hole in the centre of the main end, with a 450 mm diameter and a 20 mm thick small end cap, which will weigh only 25 kgLevel-IIreducing machineThe snail axle in the case, with small end cover to be removed for disposal without a car tossing, reduced the processing time from the previous four hours to approximately 1.5 hours and improved the test efficiency。

The on-site staff analysed the causes of the failure of the snail axle under pressure and improved governance in the areas of modification of process protocols, improvement of electrical chain protection, adjustment of the electromagnetic brakes, maintenance of the lubrication system and manipulation of the roller, as well as improvements in the main end cap under pressure, as described briefly below. The brakes of the pressurized device are controlled by a genuine brake (EMC). The crew is made of electrics, gears, snailsSa series deceleratorComposed of cogs, human cogs, acoustics, acoustics, acoustics, workspaces, etc. Designed to press 745 mm, 12. 5-25. 1 mm per second, driven by 2 37okw power units, moving both sidesSa seriesGeared motorTo act, the Electromagnetic Isolator is connected in the middle, and the unconnection of the Electromagnetic Isolator is able to reconcile the side of the pressured screw to the synchronous requirements. These are the structural features of the four reversible mill electromechanical pressurized device that we analyzed to create the pressurized machineSa series deceleratorThe reasons for the failure of the snail axle were taken as a precautionary measure and the test experience was drawn up。

Press the machineSa series deceleratorPrecautionary measures for the arcs of the medium snails: 2) In the procedure, a fair-tracking system is developed to calculate the fair-down and downfalls for different types of steel and different plate sizes. The effective implementation of preventive measures has significantly reduced the frequency with which snails have broken down. 3) Check the pressurized machines according to scheduleSa series deceleratorThe lubrication system to ensure that indicators such as the cleanness of lubricants are met and that pressure and traffic are in accordance with design specifications. The four irradiable reversible rollers are important equipment for the medium-heavy plate processing of the steel plant, and their work is to pressure the rollers to process them through two relatively rotating rollers and to transform them into plastic. Roll-overs are made by electric power through series of moving structures. 4) The tightness of the justly re-engineered embraces cannot be over-stretched in order to prevent the twitch control deviations caused by inertial automatic pines, nor can it be over-stretched in order to prevent the forces of automatic twirl under the force of the rollerServo motor reducerAxle crashes. 5) The selection of run-off data or rudder pads should be clearly exclusive and can be based on a two-person confirmation track system. It is recommended not to use too high a pressure and bite to reduce the impact on the crushing screw and the crushing of the nut, which would effectively reduce instant bite-blocking incidents in the pressurized device and reduce the incidence of instant bite-blockingSa series deceleratorsnail axle malfunctioning. http://boserlgearreducer.com/product/list-saxilijiansuji-cn.html