S seriesreducing engine output axis. A fixed side is also added between the twin planet wheel axis and the elliptical and elliptical gears, respectively. however, the main obstacle to the development of a rolling-barrel pump is the lack of reliable and well-used switching devices, starting with the design of a rolling-barrel switch, for example, with a detailed well, which is designed to be used as an exampleDouble- power decelerator(c) a non-circle gear rotation device with a core component. in order to verify that the output axis of the s seriesreducing non-round-cycle components can move according to the theoretically analysed pattern, it needs to be simulated by motion, and before the non-turnal planetary parts movement is simulated, it is necessary to confirm that the elliptical gears built by the s seriesreducing machines can be properly combined。

Retain the S seriesreducing machine model into the Parasolid pattern, and then import it into the polygonal kinetic analysis software ADAMS. The imported file shows that the gravitational direction is -z-axis, the system unit is MMKS, and the imported model has no quality information. The measure is available at 20s, i.e., at a time when the pole is spinning at 720°, to the corner of the unit ' s output axis, and at six times/min, on the basis of the analysis in chapter II, the theoretical calculation curve of the S series decelerator to the angle of the output device ' s output, comparing the two graphs to the two graphs, i.e., i.e., the i.e., the i.e., the i.e., the i.e., the i.e., the theoretical calculation value。Servo motor reducerAngular velocity changes in the unit ' s output axis for a period of 20s, which is being rotated to 720°. Once the S series ofreducing machines have been installed, they can be simulated, and the S series ofreducing machines can see that the rolling patterns and theoretical analyses of the output axis are basic, following the continuous rolling of the input axis, and that the S series ofreducing axes have a regular positive reverse. The current S-series decelerators are becoming increasingly inappropriate for the current oil field requirements for long- and low-scrambling, while the S-series decelerators easily reconcile their scramblings with the conclusion that they are more directly confronted. A fixed side segment was added between the rods and the two poles, with a 2 m drive in the centre of the turn of the poles and an angular velocity of 36deg/s of the 6/min-time poles, so that the cornering was driven by 36.0d*time between the rods and the ground。

In order to verify that an elliptical gear model is able to integrate normally, a motion simulation of the elliptical gear rodging process is required. An elliptical gear between the s-reducing gear and a fixed axis of the s-reducing gear is fixed and connected to the ground. The method is generic and can be designed for different wells. create two axes and assemble two identical elliptical gears, as shown in figure 4-12, series sGeared motorThe two ellipse gears are interconnected with the corresponding axes and the ellipse long axis is reunified at a distance of 282.8488 mm from the centre of the two ellipse gears. It can be seen that, as a result of the fixed deviation between the glyph glyph glyphs and the desired values, there are a few velocities in the axle of the output axis of the planet ' s rotor system, which, if the contours were more correct, would weaken, as shown by the rough line in the output axle velocity curve obtained from the use of the Bartworth digital filter to filter the high frequency. In accordance with the motor relationship, the non-circle rotational parts are added to the motion side. Ellipse gears and output axes are added to the fixed side, and scrolled side by side between the output axis and the earth. The centre of the rotation is at the left focus of the elliptical ellipse, which streamlines the non-round planetary rotational components of the S-reducing machine by removing parts such as bolts, cylinders, axle bearings, bearings, etc., and retaining only the main motor parts and the simplified model. ADAMS has a special measureHelical-worm gearmotorThe function can measure parameters such as the, acceleration, etc. of the component or the angle by creating the Marker point. http://boserlgearreducer.com/product/list-wolunwomenjiansuji-cn.html