The 1,400w power plant was used on the ice machine. If you do not choose a model, you can consult the technical staff of the boserl camera-reducing machine. the new pressurized room is in the lower of the ice maker, there is a compressor in the back of the compressor room, there is a partition in the front pressurized room, there is a partition in the front of the compressor, and there are two corridors on the right side of the compulsor, the base and the upper roof of the compulsor, on the right side of the wind, on the left side of the vent, and on the left side of the ventilator, there are air vents in the front of the ice maker in the front and the back of the ventTilt gear brakesThe driver can heat the air outside the ice machine by entering the windway into the pressurized room, exchanging the hot air from the pressurized room, then excreting it from the vent and taking the heat from the pressurized room. On the basis of the above, this vent further accelerates the flow of internal and external air in the pressurized room, further improves the dissipation effect in the pressurized room, and achieves a full-square, stereodispers. In the process of improving the ice machine, a user recently asked for the use of the 1,400-w power plant with the 1,400-w machine on his ice-making machine, so how many types of velocity-reducing plant should be used to satisfy the user's needs? let's look at the details of the equipment and the undercoverGeared motorThe selection requires attention on a number of matters. There is also a vent on the back of the ice machine. So let's look at some details of the user's equipment before we go and select the corresponding model and the parameters that match it. The out-of-icing of a small electric ice machine is done by relying on an electric generator by the temperature controller, and the water is collected by a water pump or an electromagnetic valve。

During the user selection process, his request was to use the 1400 w power plant with the pv manufacturer for use by his ice maker, at a time when he did not provide the relevant parameter requirements, so it was not easy to select the corresponding pv manufacturer model and the corresponding functional parameters for use in the selection. at this point, the user's ice machine consists of a bottom, rubber pad, power, stubble key, a gear-pusher manufacturer orServo motor reducer, revolving axle, poles, shaking arms, electric stretcher poles, cutters, ice freezers, non-disturbing columns, pedals, vertical poles, crossbars, ski rubber belts, bolts, bolts, bolts, rubber caps, etc. The widespread use of small electric ice machines is largely limited by the relatively high capital of temperature controllers, electric machines, pumps and electromagnetic valves. An ice-cutting device is also present on the ice-making machine, which is attached to a rotor at the output axle of the electric power, which is connected to the rotor by carding by the peri-velocity-reducing manufacturer at the top of the rotor, which is fitted to the right side with a roller arm, which is fitted to the right side of the pole, which is connected to the right side with the shaking arm, which is connected to the electric stretcher, which is connected to the cutter at the bottom of the electric stretcher, which is placed on an ice frame at the right side of the base, which is placed on the lower side of the cutting machine, which is equipped with a non-disrupting column on the base of the ice wall, with a non-disrupting column number of four, with a rectangular fixed to the bottom of the ice shelf, and a cushioned foot on the bottom of the undisturbing column。

In the heat of summer, there is a greater desire for cold drinking or for temperature, so that some indoor ice playgrounds or cold-drinking shops are in the market. On the above basis, the vents accelerate the flow of air within and outside the pressurized room and the dissipation effect of the progressive pressurized room. The return of the chilled heat wheel inside the pressurizer is not influenced by the position of the ice maker, even if the ice maker is embedded or placed at the corner of the wall, and the heat exchange is good and does not affect the ice maker ' s capacity due to the excessive temperature of the air inside the pressurizer. And there's a vent on the lower side of the back of the ice machine. but there are no detailed parameters in either device, so in this case his 1400w power is not able to select a matching type of a camera-reducing plant for use, and at this point you can choose the type of plant where the camera-reducing plant isHorizontal reducerThe production plant and the F-series camera-reducing machine match. But the need to make ice or snow in the heat of summer is for mechanical support to reduce the environment to meet such a requirement. http://boserlgearreducer.com/product/list-rxiliijiansuji-cn.html