An annex to the r seriesreducing machines. Usually, the lid of the examination hole is pinned to the lid. During the work of the repulsor r series, the temperature in the case increases, the gas swells and the pressure increases, so that the hot air in the case is free to excrete, so as to maintain the internal and external pressure balance of the case, so that the lubricant does not leak along other cracks, such as the surface of the case or the axle seals, and usually sets up a vent in the chest. With hexagon bolts fixed on the body of the box, the axle bearings at the outer axis are pierced and contain seals. In order to enhance the sealing effect, the bolts are usually fitted with water glass or sealed glue on the section of the case at the time of assembly, and therefore often are difficult to open when they are removed because of the glue. The strength of the convection bearings is to disassembly, adjust the axle bearings, but to the extent of the embedded axle bearings, the parts are larger in number and size, and the appearance is uneven. gas surface indicator, check r seriesGeared motorThe height of the oil surface of the internal oil tank is often the maintenance of a suitable quantity of oil inside the tank, which is easily observed in the tank, and where the oil surface is not disturbed, with oil surface indicators. The spin-starter screws can be covered. A symmetric case should be symmetrically configured to avoid misloading. For the purpose of checking the condensation of the moving parts and injecting lubricating oil into the boxes, the holes should be installed at the appropriate position of the contents. The axle bearings have both cavity and embedded。

We all know thatAn umbrella gear-reducing machineThey consist mainly of moving parts (patrons or snails), axes, bearings, boxes and their accessories. Its basic structure consists of three main sectors: gears, axes and bearings, boxes, and annexes to the r series ofreducing machines, two of which we have already said before, so why are they special today? It may be thought that the annexes are not very important, that they are only annexes, that they are wrong, that they are perfect for the assembly and production of the r-series slowing machines, that any of the parts in them are related to the entire structure, and that we cannot assume that they are useless. a small r-series slasher can also have no bolt bolts, with a pick-up to open the hood, the size of which can be similar to that of a cam-link bolt, as stated above, each part is responsible for different tasks, with messages transmitted between parts and parts to form a complete r-series scalding machine, without, without, without parts and without them, and without themSecond-stage brakesNow, it's true that details determine success and failure, and it's true that it's because we, boserl, focus on every detail and bring great services and products to our clients that they love。

The bearing covers are the fixed axle position of the axis parts and bear the bearing of the axle bearings, which are sealed off at both ends of the bearings. The perforation, which is located on the top of the top covers, can directly observe the collage of the gear. When oil snails are pumped for oil, the discharge oils and detergents shall be placed at the bottom of the tank, at the lower position of the tank, and the oils shall be blocked at normal times by the snails, and leakproof gaskets shall be placed between the snails and the hulls. in order to ensure the normal operation of the r-seriesreducing machines, in addition to giving adequate attention to the structural design of gears, axes, bearings and boxes, consideration should be given to:Horizontal reducerfair-track selection and design of support parts and components such as lubricated oil tank oils, oil discharges, examination of oil surface height, processing and disassembly tests, precise positioning of the lids and the seat, suspension, etc. the positioning to ensure that the accuracy of the axle bearings during the manufacturing process is maintained at each time the lid is removed, shall be placed in front of the precision-processed axle bearings and on the cones of the frame. for this purpose, ~2 screws are often processed in the appropriate position of the lid to connect the cam, or a ~2 screws are rotated to the cylindrical end of the trunk or to flat-open a bolt. http://boserlgearreducer.com/product/list-rxiliijiansuji-cn.html