Three electric retrenchors have a set of ecstasy checks. Example 660 vy, 380va indicates that 660 v uses the y-form approach, while 380 v uses the a-form approach. Corresponding voltage values and wiring are stamped on the stamp. Three power-reducing machines have a set of direct-on-line or star-triangular start-up, and the wiring boxes of a single- scale machine usually contain six contours and at least one local end. Prior to the suspension, a check must be made for damage to the bolt or entrail on the electric power. Before connecting the machine to the power, it must be handled in accordance with local regulations. Dismantling all connection lines in the connector box. Power sets can only be installed with churning ears. three electric units when the end of the line is connected and when the end of the machine moves in the direction of the axis, and the sequence of the line l1, l2, l3 is connected to the corresponding end of the line, as shown in graph 1Geared motorOne set turns to a clockwise direction. It is strictly forbidden to use a set of rotors that have been damaged. For the three power-reducing machines, a set of machines with short cylindrical rolls and/or cpr bearings, it is necessary to be fitted with a fastening during transport. It is recommended that the axes be rolled by hand on schedule to prevent the movement of grease. The operational condition is that the machine is used in industrial transmission devices with normal ambient temperature limits of -25°c to +40c and a combined high altitude of 1,000 m. Direct on-line start-up (dol): y-shaped or a-forming can be used. prior to the suspension, the bolt must be tightened。

They can only be used for the lifting machine, which is prohibited when connected to other equipment. In the case of a single-way wind machine with a single motor reduction gear, it is necessary to ensure that the corresponding shift corresponds to the direction indicated by the arrow on the machine. The specification characteristics of the electrolyte capacitors (if installed on a single-phase generator) require “reorganization” treatment for storage for more than 1-2 years. A set of three power-reducing units immersed in sea water usually requires rewiring. The necessary safety equipment to prevent accidents must be installed and operated in accordance with local norms. The machine must be installed and used by qualified staff who are aware of the relevant security requirements. For the same type of power, because of different output valuesGearbocThe distribution of components and the effects of assistive equipment vary in their focus. It is necessary to unplug (if any) the drain hole during the baking process. The electrical resistance value determined in the context of 25C must exceed the corresponding baseline, i.e. 10MQ (measured using the rocking table of 500Vdc). It is necessary to ensure the use of accurate equipment for the suspension and to ensure that the size of the hook is applied to the corresponding churning. Upon completion of the motorization of the slasher gear, the circuits must be discharged to avoid the risk of electroshock. The baseline value for ecstasy follows a corresponding reduction of 20°C for ambient temperatures. If necessary, the position of the bolt must be regulated using the appropriate gasket. Details can be obtained from ABB ' s sales office. In order to change the above-mentioned shift, it would be possible to switch any two wire cables. Star/triangular start (V/A) power voltage must beServo motor reducerThe rated voltage, which is based on a gill, must be stored indoors in a dry, smooth and dustless state。

Certain special machine applications require special protocols (e.g., the use of the frequency transformer provided); during normal operations, it is hot to touch the shell of the machine; and for small power units that are directly connected to the power supply through a set of heat-sensitized switches for three power-reducing machines, they can be activated automatically. Unprotected machine surfaces (axis and Frank) need to be protected with corrosive paint. If you have a condenser, you can keep it in a state of incentive. Prior to debugging and in case of doubt about the encirclement humidity, the corresponding ecstasy can be determined. Follow-up points:Induction Motor 3PhA set is used for step-by-step applications; if the set of three electric retrenchors does not meet the corresponding resistance baseline, it indicates that the circuits are too wet and must be dried. For double-, single-phase and special tilt gear reduction motor s in one form, the powering method must conform to the protocol within the connector box. The temperature of baking must be 90 C°C and last 12-16 hours, while when the baking temperature is 105 C, it must last 6-8 hours. http://boserlgearreducer.com/product/list-ffxiiejiansuji-cn.html